
450–800 kW with the gas mixed inside the inlet tract, running a higher compression and boost ratio than the external-mix engine. Used for single-set or paralleled generation, and for compressor, oil pump and water-injection pump drive.
Internal-mix units inject gas directly into the cylinder, which holds rating on lean gas and gives a faster load response than external mixing.
| Genset model | Engine model | Rated power (kW/kVA) | Voltage (V) | Frequency (Hz) | L×W×H (mm) | Net mass (kg) | Fuel |
|---|---|---|---|---|---|---|---|
| 400GF-MK1 | 12V190Z_W-2 | 400/500 | 400/230 | 50 | 5120×2040×2678 | 12000 | Coal gas |
| 450GF-T1 | G12V190Z_DT-2 | 450/562.5 | 400/230 | 50 | 5120×2040×2678 | 12000 | Natural gas |
| 500GF-TK | G12V190Z_T-2 | 500/625 | 400/230 | 50 | 5120×2040×2678 | 12000 | Natural gas |
| 500GF-MK1 | 12V190Z_W | 500/625 | 400/230 | 50 | 5120×2040×2678 | 12000 | Coal gas |
| 500GF-LK | G12V190Z_L-2 | 500/625 | 400/230 | 50 | 5120×2040×2678 | 12000 | Refinery gas |
| 700GF-TK | G12V190Z_T | 700/875 | 400/230 | 50 | 5120×2040×2678 | 12000 | Natural gas |
| Engine model | Rated power (kW) | Speed (r/min) | Compression ratio | Cylinder configuration | L×W×H (mm) | Net mass (kg) | Fuel |
|---|---|---|---|---|---|---|---|
| 12V190Z_W-2 | 450 | 1000 | 10 : 1 | 12 cylinders, 60° V | 2785×1628×2437 | 5300 | Coal gas |
| G12V190Z_L-2 | 550 | 1000 | 10 : 1 | 12 cylinders, 60° V | 2785×1628×2437 | 5300 | Refinery gas |
| 12V190Z_W | 550 | 1500 | 10 : 1 | 12 cylinders, 60° V | 2785×1628×2437 | 5300 | Coal gas |
| G12V190Z_T-2 | 600 | 1000 | 10 : 1 | 12 cylinders, 60° V | 2785×1628×2437 | 5300 | Natural gas |
| 12V190Z_Z | 700 | 1500 | 10 : 1 | 12 cylinders, 60° V | 2785×1628×2437 | 5300 | Biogas |
| G12V190Z_T | 800 | 1500 | 10 : 1 | 12 cylinders, 60° V | 2785×1628×2437 | 5300 | Natural gas |
| 12V190Z_T | 800 | 1500 | 10 : 1 | 12 cylinders, 60° V | 2670×1588×2538 | 5300 | Natural gas |
Heat rate is quoted on lower calorific value; derating for methane number and altitude is applied at quotation.
Translated from the 190 Series Internal Mixing Gas Engine datasheet issued by BOMCO. Figures are factory values in SI units; the quotation confirms the exact build for your order.
We build 190 Series Internal Mixing Gas Engine in Baoji and test each unit against the figures above before it leaves the works. Our engineers set the rating point at commissioning to suit your fuel, altitude and ambient conditions, and we hand over the signed test sheet with the unit.
Tell us the duty you have in mind for 190 Series Internal Mixing Gas Engine and we will confirm which row of the table applies, or quote a special build when none of them fits.
Internal mixing with raised compression and boost, plus higher swirl ratio and a high-energy ignition system. That is the detail a catalogue listing usually leaves out, and the one that decides whether the unit suits the well in front of you.
Internal mixing lets us raise compression and boost without detonation, which is where the fuel consumption advantage comes from.

Higher compression and boost than the external-mix frame, for single or paralleled generation, the build a gas engine genset manufacturer offers when fuel is dry and load is steady.

190 Series Gas Engines

190 Series Gas Engines

190 Series Diesel Engines

190 Series Diesel Engines