Drilling, workover and well service equipment · Baoji, Shanxi, China
info@bomcochina.com Service centres: UAE · Kuwait · Oman · Saudi Arabia · Egypt
Downhole Lift

Electric submersible pump systems for high-rate oil wells

ESP systems built as one string: motor, seal, gas separator, pump and cable sized to your casing, rate and temperature, tested before dispatch.

Scope Supplied as a system rather than a single model. Ratings, dimensions and interfaces are issued as a data sheet with the quotation.

Request data sheet →

Specifications

String data

Figures below are the group pump works catalogue range. The quotation fixes the stage count, motor length and cable size for your well.

Pump type
Multistage centrifugal, radial and mixed-flow stages
Displacement
15 – 4,700 m3/d
Head
Up to 3,500 m
Working temperature
90 – 180 °C
Casing sizes
4-1/2 in to 9-5/8 in
Series
Four body series, more than 200 build combinations
String components
Motor, seal section, gas separator, pump, cable, surface panel

Figures taken from the ESP Systems (Electric Submersible Pump) data sheet issued by BOMCO. Values are nominal and the quotation confirms the build for your order.

A submersible string is a motor, a seal section, a gas separator, a multistage centrifugal pump and a cable, all of it running on the production tubing below the wellhead. Nothing in that string is standard: the stage count follows the drawdown you want, and the motor length follows the power the stages absorb.

We build the string as one order, from the motor through the protector to the pump and the cable termination, so thrust load and shaft alignment are settled on the test bench here rather than at the wellsite.

We size the string from the completion down: casing, setting depth, water analysis and the inflow you expect over the first two years. Our bench runs the assembled motor, seal and pump as one unit, and the record we sign is the one the operator keeps for the next workover. Where a well is gassy we would rather add a separator than ask the stages to digest free gas, and we say so before the order is placed.

Capability

What this system covers

  • Duty rangeDisplacement from 15 to 4,700 m3/d, heads to about 3,500 m, working temperature from 90 to 180 °C, in four body series and more than 200 build combinations.
  • Casing fitStrings are sized for 4-1/2 in through 9-5/8 in casing. We check the clearance against your completion diagram before the motor diameter is frozen.
  • Sand, scale and gasStage geometry and bearing material carry the string through sand-laden, scaling and gassy wells; the metallurgy and the seal elastomer are chosen against the produced-water analysis.
  • Gas handlingA separator or advanced gas handler sits ahead of the intake where free gas would otherwise blank off the first stages.
  • Surface packageSwitchboard, transformer and junction box are matched to the motor voltage and current, so the whole string is covered by one warranty and one test record.
Questions we get

Selection notes

Can you build a string for a casing size we already have?

Yes. Send the casing size, setting depth and completion diagram; we size the motor outside diameter, the pump stages and the cable to that clearance, and confirm all three in one drawing.

How is the motor rating decided?

From the power the stages absorb at the design rate, plus the intake section load, then corrected for supply voltage and ambient temperature at the wellsite. The nameplate figure is the result of that calculation, not a catalogue default.

What happens with sand and free gas?

Sand is handled by stage geometry and bearing material, gas by a separator or gas handler ahead of the intake. Both are configuration choices settled from well data, so they cannot be added later as an option.

Supply notes

How this system is ordered and shipped

Motor, seal and pump are assembled and run as one string on our bench, then strip-tested and crated with cable and surface panel, so a rig crew does not have to match parts from three suppliers.

Every string ships with a signed record for head, rate, efficiency, amperage balance and insulation resistance at the design point.

We are an electric submersible pump manufacturer as well as an ESP system supplier: the ESP pump for oil well duty is quoted together with the submersible motor oilfield crews would otherwise have to source from a second vendor.

We test the pump, motor, seal section and cable as one string before it leaves, which is the difference between a package and an electric submersible pump supplier that ships the parts separately.

Other systems in this line

Systems and packages

Where this system is used

Quote the ESP Systems — Electric Submersible Pump against your project

Request a Quote →
BOMCO
Request a Quote